Reach Forklift
From: £240.00
Reach Forklift Training is Independent Training Standards Scheme & Register (ITSSAR) accredited. Reach forklift Trucks are primarily used in warehouses. They are used to Stack / De-stack products at greater heights. This forklift truck is also helpful when aisle widths are narrower allowing for increased storage.
D1 up to 8m lift height
D2 above 8m lift height (training only available on customer sites)
Courses for all experience levels
N
Novice Level Training
Trainees with little or no previous experience operating the relevant truck.
E
Experienced Forklift Training
Trainees with relevant experience who have not received any approved training, or certification is expired (over five years from issue date).
R
Forklift Refresher Training
Periodic forklift refresher training for experienced operators who hold an accredited certificate issued in the last five years.
C
Forklift Conversion Training
Training on a truck of a similar level to the one that the operator has already been trained, tested, and certified on.
What’s Included
- Train with an ITSSAR accredited Forklift instructor who will build your knowledge and comprehension around the safe operating and use of a Reach Forklift Truck.
- Ability to complete your course at one of our training depots with dedicated warehouse and training facilities.
- Or, depending on your location, complete your course at your own site
- Gain Certificate of completion after your course.
- Printed certificate and ID card available at an extra cost.
Course Modules
The following list is the elements that make up a novice reach truck course. For experienced operators, safety refresher and conversion courses the list may be shorter.
- Course induction
- The need and reasons for training and statutory requirements (HASAWA 1974, Provision and Use of Work Equipment Regulations 1998 (PUWER) Lifting Operations and Lifting Equipment Regulations (LOLER) 1998 & L117 Approved code of practice
- Introduction to equipment/control familiarisation/principles of operation
- Identification/use/adjustment of attachments in pre-determined positions including forks
- Recommended mount and dismount
- Introduction to motive, steering controls and practice
- Basic steering exercises – simple courses
- Advanced steering exercises – figure of 8/chicane/90° approaches
- Battery charging procedures/maintenance
- Operator safety code and relevant handout
- Daily pre-use inspections/refuelling procedures
- Engineering principles/rated capacity/stability
- Simple hydraulics (theory)
- Introduction to hydraulic controls, handling empty pallets low-level
- Load types/handling and weight assessment
- Stacking/de-stacking at low, medium and high levels on industrial racking*
- Stacking/de-stacking at low, medium and high levels bulk stacks*
- Stacking/de-stacking at low, medium and high levels cup post pallets*
- Manoeuvring with loads/ramps and inclines/handling awkward loads*
- Relevant safety film
- Vehicle loading and unloading (theory)*
- Vehicle loading and unloading (practical)*
- Multi-choice theory test
- Pre-use inspection test
- Practical skills test
* To be covered where relevant to operation or facilities permit
Course Benefits
ITSSAR Accredited Training
Dedicated Training Areas & Racking
Experienced Instructors
Reach Forklift & Training Hardware Provided
Course Durations
1 Day
3 Days
5 Days
Durations available for this specific course.
Forklift Requirements
To complete training to operate a Reach FLT, you must be at least 16 years old. The Forklift you are planning to operate must be the Truck you are completing training and testing for.
Ongoing Requirements
It is advised you should complete refresher training every 3-5 years to keep your Reach certification in date. As stated in the ACOP L117 You can complete this training in 1-day. We also offer the experienced operator training if you cannot locate your certification.
Test Requirements
You will complete three tests in total.
- Theory Test.
- Pre-use Inspection Test.
- Practical Skills Test.
Theory Test:
The theory-based test will demonstrate your knowledge on safe operating and maintenance for Reach trucks. These will be in conjunction with what you have learnt during your training course. The test includes both 5 open and 20 multiple-choice questions, which will establish your knowledge when it comes to operating and safety.
Each question set provides the chance to receive 4 marks, with a total of 100 marks available. You must get 80% of all questions correct (80 marks) to pass the theory test.
Pre-use Inspection test:
The pre-use checks test is designed to evaluate an operator’s ability to correctly asses and check the key components of the reach forklift to ensure the vehicle is safe and fit for use and includes checking the key areas of the forklift listed below.
Walkaround Visual Checks:
- Lights
- Steering
- Audible Warning Devices
- Hydraulics
- Mast
- Mast/Rollers Slides
- Lift Chains
- Chain Pulleys
- Rated Capacity Plate
- Hydraulic Controls
- Starting Procedure
- Carriage Plate
- Back-Rest Extension
- Reach Leg Channels
- Fork Arms
- Tyres
- Wheels
- Drive and Breaking
- External Condition
- Operating Position
- Operators Seat
Functional Checks:
- Lights & Warning Indicators
- Horn and Warning Alarms
- Hydraulic Controls
- Drive and Braking
- Steering
- Electric
- Electrolyte Levels
- Cable Connections
- General Cleanliness
- Battery Security
Practical Skills Test:
The practical test will show your instructor that you have taken on the competencies and are able to implement them when using a Reach FLT. This consists of how safely you operate the machine, and penalty points will be given if you complete a task which is deemed unsafe, such as erratic and improper use of the controls.
The practical skills test has a maximum allowance of 40 penalty point within a given time.
You will first show your instructor that you can properly complete the pre-use checks.
Once successfully completed, you will then need to complete the following and show you can do so safely:
- Mounting, starting and stopping the truck
- Drive both forwards and reverse, including braking
- Steer accurately
- Correctly place a load on the forks
- Use the hydraulic controls correctly
- Show that you can judge the position of fork tips at varying heights
- Stack and de-stack at varying heights safely
- Be cautious of the working environment and judgment of speed, height, width and distance from within the confines of the machine
- Dismount and park the truck
These are all considered critical skills which show safe application methods throughout your test.
Further Training
While refresher training can be completed for the Reach Forklift, you can opt for a conversion course, which will take the skills you have already acclaimed through your Reach training, and implement it with another Forklift Truck, such as a Counterbalance FLT.
You can choose to upskill and complete our Forklift Instructor course, so you can train other individuals in getting their FLT certification.
Earning Potential
Reputable Salary Checkers estimate the following for a forklift operator across the South Coast:
While all efforts have been made to ensure the accuracy of this information, we suggest conducting your own research and use these figures for information purposes only.
- Reach Forklift Operators in Portsmouth averages £27,871 per annum
- Reach Forklift Operators in Reading averages £27,495 per annum
- Reach Forklift Operators in Worthing averages £32,638 per annum
- Reach Forklift Operators in Havant averages £27,585 per annum
This doesn’t consider any additional job roles you have within your current industry such as being a warehouse operative, warehouse manager or distribution assistant.
Who is this course for?
This course is for those at least 16 years old, and looking to gain your FLT certification for a D1 category truck (Reach FLT).
A good understanding of spoken and written English is required for this course. Translator may be required to assist if English is not the first language as required within ITSSAR standards.
What can I operate with a Reach Certification?
You can only operate a Reach Forklift truck with this certification. If you need to use any other type of FLT, but have recently obtained the Reach FLT certification, then you must complete conversion training and tests for that particular Forklift separately.
Under no circumstances should you try to operate any FLT you do not have the certification for.
What will you receive upon successful completion of this course?
Once you pass your Reach Forklift course, not only will you receive your ITSSAR certification, but you will also obtain a 2 Start certificate of completion. You can also receive an ID card for the Trained Operator Passport Scheme (TOPS) at an additional cost. – this is available from ITSSAR directly.
Frequently Asked Questions
What is Reach Forklift Operator Training?
Reach Forklift Operator Training is a specialized course designed to teach individuals how to safely operate reach trucks, which are forklifts with extended arms for lifting loads at height and in narrow aisles. The training covers safety protocols, proper handling techniques, and equipment operation to ensure a safe and efficient work environment.
How long does it take to complete Reach Forklift Operator Training?
The duration of Reach Forklift Operator Training typically ranges from 1 to 5 days, depending on the training provider and the experience level of the participants. The training includes both theoretical instruction and hands-on practice to ensure competency in operating the forklift safely and effectively.
Why Choose 2 Start?
Reputable
High Pass Rates
Established in 2008
Industry Leading Training Provider
Independently Owned
6 Dedicated Training Centres
VIEW COURSESTrusted
4.9 Star Rating on Google Reviews
DVSA Approved 3a Examiners
DVSA Approved Test Centres
APAR Approved Training Provider
RLI Certified LGV Instructors
BOOK NOWAccredited
Accredited Instructors & Courses
Regular Accrediting Body Audits
Exceptional Audit Pass Marks
Listed With 9 Accrediting Bodies
Verifiable Accreditations
THE TEAM1 Past student reviews for Reach Forklift
Only logged in students who have purchased this course previously may leave a review.
Harry Jackson –
Gary is another good instructor with you guys. He has kept today very engaging and has got me confident with the Reach despite only a day on it.